HowToFixWiFiSimple fixes  •  Better connection
Devices and Use Cases

How to Put New Wifi on Ring Camera: Change Network Settings Fast

Introduction If you have replaced your router, changed your internet provider, renamed your network, or updated your Wi-Fi password, your Ring camera may stop sending alerts, recording events, or showing live view. The good news is that you usually do not need

HowToFixWiFi

Introduction

If you have replaced your router, changed your internet provider, renamed your network, or updated your Wi-Fi password, your Ring camera may stop sending alerts, recording events, or showing live view. The good news is that you usually do not need to delete the device and start over. This guide explains How to Put New Wifi on Ring Camera? quickly, whether you are using a Ring doorbell, indoor camera, outdoor camera, floodlight camera, or a Ring Chime Pro. The exact menu names can vary slightly by app version and device model, but the overall process is the same: connect the Ring device to the new network, confirm it is online, and test motion, live view, and notifications.

Before you begin, make sure your new Wi-Fi network is working on your phone. Stand near the camera with your phone, and keep your Wi-Fi password available. If possible, write down the old network name and password too, because some Ring setups are easier when the new router uses the same details as the old one. Throughout this article, the primary keyword How to Put New Wifi on Ring Camera? is used to describe the full process of changing network settings without unnecessary resets.

What Changing Wi-Fi Means for a Ring Camera

Changing Wi-Fi on a Ring camera means updating the saved network name and password inside the device. Ring cameras do not automatically follow your phone to a new network. They store the credentials from the original setup, and if those credentials no longer match your router, the device becomes offline. In many cases, the camera itself is fine; it simply cannot reach the internet.

When you update the network, the camera reconnects to the Ring cloud, resumes recording according to your plan, and restores live view. Your motion settings, zones, shared users, and device name usually remain the same. However, if the camera has been offline for a long time, you may need to wait a few minutes for thumbnails, event history, and device health information to refresh.

There is an important difference between changing Wi-Fi and resetting a device. Changing Wi-Fi keeps your settings. Resetting removes the device from your account or restores factory defaults. You should only reset if the normal network change process fails or if you are transferring the device to another owner.

Before You Start

Preparation prevents most failed connections. Start by confirming that your phone is connected to the new Wi-Fi network and that the internet works. Open a browser or speed-test page and verify that pages load normally. Then check your Ring app and make sure it is updated to the latest version. An outdated app can hide menu options or fail during setup.

Next, locate the physical setup button on your Ring device. The location depends on the model. Many battery doorbells have a button on the back or side. Wired doorbells may have a button under the faceplate or on the side. Indoor cameras often have a setup button on the top or back. Floodlight cameras and spotlight cameras may have a button near the bottom or under a cover. You will press this button during setup mode.

If your camera is battery-powered, check the battery level before starting. A low battery can cause setup to fail midway. Charge the battery fully if possible. If the device is hardwired, make sure power is on and the transformer is working. For doorbells, you can test power by checking whether the old doorbell chime rings or whether the Ring light turns on.

Finally, decide whether you want to keep the same network name. If your new router can use the same SSID and password as the old one, your Ring camera may reconnect automatically. This is often the fastest solution. If you cannot use the same credentials, continue with the steps below.

How to Put New Wifi on Ring Camera? Fast Method

The fastest standard method uses the Ring app while the camera is still online or recently offline. If the camera appears in your device list, you can often change the network without pressing any physical button. If it is offline, the app may still let you start the process, but you will usually need to put the device into setup mode.

  1. Open the Ring app on your phone.
  2. Tap the menu icon or your account profile, depending on app layout.
  3. Select Devices.
  4. Choose the camera, doorbell, or Chime Pro you want to update.
  5. Tap Device Health.
  6. Look for Change Wi-Fi Network, Reconnect to Wi-Fi, or a similar option.
  7. Follow the on-screen instructions.
  8. When prompted, press and release the setup button on the Ring device.
  9. Select your new Wi-Fi network from the list or enter it manually.
  10. Enter the Wi-Fi password carefully, paying attention to uppercase letters and symbols.
  11. Wait for the app to say the device is connected.
  12. Test live view, motion detection, and notifications.

If the app cannot find the device, move closer to it. Ring setup often uses a temporary direct connection between your phone and the camera, so distance matters. Also disable VPN on your phone during setup, because a VPN can block local device discovery.

Method 1: Change Wi-Fi Through the Ring App

This method is best when the camera is still online. It is the least disruptive because you do not remove the device from your account. The app walks you through the connection process and verifies the result.

Step-by-Step App Method

  1. Connect your phone to the new Wi-Fi network.
  2. Open the Ring app and sign in.
  3. Go to Devices and select the camera.
  4. Open Device Health.
  5. Tap Change Wi-Fi Network.
  6. Confirm that you want to update the network.
  7. Put the device in setup mode if requested.
  8. Choose the new SSID.
  9. Enter the password.
  10. Wait for the connection test to finish.

During this process, your phone may temporarily disconnect from your home Wi-Fi and connect to a Ring setup network. This is normal. Do not close the app until it says setup is complete. If you are asked for location permission, allow it, because Wi-Fi scanning on many phones requires location access.

Verify the Connection

After the app says connected, do not stop there. Open live view and wait for the video to appear. Then walk in front of the camera to trigger motion. Check whether you receive a notification. Finally, return to Device Health and review the signal strength. A weak signal may mean the camera connects but drops later.

Method 2: Use Setup Mode and the QR Code

Some Ring devices and app flows use a QR code, especially during initial setup or full reconnection. If your camera is offline and the app cannot change the network normally, setup mode may be the better route. This method is also useful after a factory reset.

  1. Open the Ring app.
  2. Tap Set Up a Device if the camera is not already in your account, or use the device-specific reconnect option if it is.
  3. Select the device type, such as doorbells, security cameras, or Chime.
  4. Scan the QR code or MAC barcode on the device or packaging.
  5. Follow the prompts to connect to the Ring setup network.
  6. Press the setup button to enter setup mode.
  7. Select your home Wi-Fi network.
  8. Enter the password.
  9. Complete setup and name the device if asked.

If the QR code is damaged or missing, many Ring devices have the code inside the battery compartment or under the faceplate. You can also sometimes manually enter the serial number or MAC address. Check the device label carefully before removing anything, and make sure power is disconnected when removing a wired doorbell faceplate.

Wired Doorbells and Hardwired Cameras

Wired Ring doorbells and hardwired cameras need special attention because power and network setup happen at the same time. If the device is not receiving enough power, it may fail to enter setup mode or may reboot during connection. Before changing Wi-Fi, check that the transformer meets the device requirements. Many wired doorbells need a transformer in the 8-24 VAC range, depending on model.

To change Wi-Fi on a wired doorbell, first turn off power at the breaker if you need to remove the faceplate. Locate the setup button, press it, and follow the app prompts. If the doorbell is connected to an existing chime, test the chime after reconnecting. For hardwired cameras, make sure the power cable is secure and the camera has finished booting before pressing setup.

If your wired device keeps disconnecting, the issue may be power rather than Wi-Fi. Low voltage can cause the camera to reboot when it tries to connect or record. In that case, solve the power issue first, then repeat the network setup.

Battery-Powered Ring Devices

Battery-powered devices are usually the easiest to move and update because you can bring them close to the router. Remove the device from its mount if needed, charge the battery, and perform setup near the router. This reduces signal problems during the initial connection.

For battery doorbells, press the setup button on the back or side. For Stick Up Cams, the button may be on the back, bottom, or under the battery cover. For Spotlight Cams, check the base or battery compartment. After pressing the button, the light should indicate setup mode. Follow the app prompts, select the network, and enter the password.

Once connected, reinstall the device and check signal strength. Battery devices often work best on 2.4 GHz because of range. If the device is far from the router, consider a Wi-Fi extender, mesh node, or Ring Chime Pro to improve coverage.

Ring Chime and Chime Pro Network Settings

Ring Chime and Chime Pro can also need network updates. Chime Pro may act as a Wi-Fi extender for compatible Ring devices, so its network connection is especially important. If you change routers, update Chime Pro first or at least ensure it is online before updating cameras that depend on it.

To update a Chime, open the Ring app, select the Chime, go to Device Health, and choose the Wi-Fi change option. Press the setup button on the Chime when prompted. For Chime Pro, check whether devices are connected through it. If cameras connected via Chime Pro go offline, reconnect Chime Pro first, then reconnect or restart the cameras.

Do not assume that updating the router automatically updates Chime Pro. It stores its own credentials. If Chime Pro remains offline, doorbell chime sounds and extended Wi-Fi coverage may stop working.

Router and Network Requirements

Most Ring cameras work best with a stable 2.4 GHz network. Some newer models support 5 GHz, but 2.4 GHz usually provides better range through walls. Ring generally recommends at least 2 Mbps upload speed per device. If you have multiple cameras, add more bandwidth. A home with four cameras may need significantly more upload capacity than a single doorbell.

Use WPA2 or WPA3 security. Avoid open networks. If your router uses MAC address filtering, add the Ring device’s MAC address before setup. The MAC address is often on the device label or in the Ring app under Device Health. Hidden SSIDs can work, but you may need to enter the network name manually. If possible, make the SSID visible during setup.

Channel selection can also matter. On 2.4 GHz, channels 1, 6, and 11 are commonly recommended because they reduce overlap. If your area is crowded with neighboring networks, try one of these channels. Also check whether your router combines 2.4 GHz and 5 GHz under one name. Some Ring devices connect fine, but others may struggle with band steering. If setup fails repeatedly, temporarily separate the bands or connect the camera to a dedicated 2.4 GHz network.

Network Feature Best Practice for Ring Cameras Why It Matters
Wi-Fi Band Use 2.4 GHz for range; use 5 GHz only if supported and close to router 2.4 GHz penetrates walls better and reaches outdoor devices
Upload Speed At least 2 Mbps per camera, more for multiple devices Low upload speed causes lag, failed live view, and missed recordings
Security Mode WPA2 or WPA3 Open or outdated security can block connection or reduce safety
Router Channel Use 1, 6, or 11 on 2.4 GHz Reduces interference from neighboring networks
SSID Visibility Visible network name during setup Makes scanning and manual entry easier
MAC Filtering Add Ring MAC address if filtering is enabled Prevents the router from blocking the camera

Troubleshooting When Ring Will Not Connect

If your camera refuses to connect, start with the simplest fixes. Reboot the router by unplugging it for 30 seconds and plugging it back in. Restart your phone too. Then try the setup process again. Many temporary DHCP or DNS issues disappear after a reboot.

Check the password carefully. Wi-Fi passwords are case-sensitive. A single uppercase letter or symbol can cause failure. If possible, temporarily simplify the password by removing unusual symbols, connect the Ring device, and then restore a stronger password later if needed. Not all routers make this easy, but it can help isolate the problem.

If the app cannot find the camera during setup, move closer. Stand within a few feet of the device. Disable VPN, mobile hotspot, and battery-saving modes that may restrict background Wi-Fi switching. Allow location permission for the Ring app if prompted. Also make sure your phone is not connected to a different network, such as a cellular hotspot.

If the device appears connected but shows offline after a few minutes, check signal strength. A weak signal can cause intermittent drops. Move the router, add a mesh node, or use Chime Pro. Also check for interference from microwaves, cordless phones, baby monitors, and thick walls. Changing the router channel can reduce interference.

If all else fails, remove the device from the Ring app and set it up again as a new device. This is more time-consuming but often resolves corrupted setup data. Only do this after trying the normal reconnect process. If the device is still under warranty and will not connect even next to the router, contact Ring support.

Tips and Best Practices

  • Use the same SSID and password on your new router whenever possible. This may let Ring devices reconnect without manual changes.
  • Update firmware and app versions before changing networks.
  • Charge battery devices before setup.
  • Perform setup near the router, then reinstall the camera.
  • Keep your Wi-Fi password stored securely in a password manager.
  • Label each camera clearly in the Ring app so you know which device you are updating.
  • Test every camera after a router change, not just the one you think is affected.
  • Check motion zones and notification settings after reconnection, because some devices may reset preferences.
  • Use a dedicated 2.4 GHz network for outdoor cameras if band steering causes problems.
  • Consider a UPS for your router if power outages frequently disrupt security coverage.

Another useful tip is to change one device at a time. If you update five cameras simultaneously and something goes wrong, it is harder to identify the cause. Start with the most important camera, confirm it works, then move to the next. This keeps your security coverage active during the transition.

Frequently Asked Questions

Do I need to reset my Ring camera to change Wi-Fi?

No. In most cases, you can use Device Health in the Ring app to change the network. Resetting is only necessary if the normal process fails or if you are transferring ownership.

Will my Ring camera connect automatically if I use the same Wi-Fi name and password?

Often yes. If the new router uses the same SSID and password as the old one, many Ring devices reconnect automatically. You should still test live view and notifications.

What if my Ring camera is offline and I cannot find the change Wi-Fi option?

Try putting the device into setup mode and using the reconnect or setup flow in the app. If that fails, remove the device from your account and set it up again.

Can I put a Ring camera on 5 GHz Wi-Fi?

Some newer Ring models support 5 GHz, but many older models support only 2.4 GHz. Check your device specifications. For outdoor cameras, 2.4 GHz is usually more reliable because of range.

Why does my Ring camera show weak Wi-Fi after reconnecting?

The device may be too far from the router, or interference may be affecting the signal. Try moving the router, changing channels, adding a mesh node, or using Ring Chime Pro as an extender.

Can I change Wi-Fi on multiple Ring cameras at once?

No. Each Ring device stores its own network credentials, so you must update them individually. Using the same SSID and password on the new router can reduce manual work.

Conclusion

Learning How to Put New Wifi on Ring Camera? is mostly about following the Ring app’s network change process, keeping the device powered, and making sure your router settings are compatible. Start with Device Health, use setup mode if needed, and verify live view, motion alerts, and signal strength afterward. If your camera will not connect, check the password, move closer, reboot the router, and consider whether power or signal strength is the real issue. With a little preparation, you can update your Ring camera’s Wi-Fi settings quickly and keep your home security system running without interruption.